Well i have finally gotten to the stage in my build where I need to get some brake lines made up for the B, need to go from 7/8th master to wilwood bias valve (which I have sorted out thanks to the kit Baz supplies) then to the original line going along the firewall and into the trans tunel to the rear brakes, I just need to make a line from the valve to the original line which has a male fitting.

For the fronts i was going to come off the MC then onto a distribution block mounted onto the wheel well in the bay, then have the line for the front right go under the rail to the mounting tab then for the left i was thinking of going along the crosmember held by some P clips and onto the mounting tab.

Been thinking on just getting some roll of wire and bending it to suit then take that to a brake place and get them to make some up with the proper fittings and flares, questions is where to go????

doesn't need to be anythign fancy just be able to make what I need and if possible located in the South East Melb area.

Cheers!

Alex

_________________
"You stay classy OzDat"

If you feel like a drive better brake's in bayswater are really good have always had fittings and bundy tube in stock when I needed them

_________________
120Y 4DOOR SEDAN SR20DE WITH ITB'S

http://datsun1200.com/modules/newbb/vie ... post494892

would they make lines up tho??? or do they just supply tubing and fittings???

_________________
"You stay classy OzDat"

I was going to say better brakes too. They can make up lines and everything.

_________________

Yeah they can but its pretty easy man. Ive got access to a flairing tool and bender if you wanted to do them yourself?

_________________
120Y 4DOOR SEDAN SR20DE WITH ITB'S

http://datsun1200.com/modules/newbb/vie ... post494892

I'll ask them for a rough price if not I'll take you up on that offer Stu, I've always wanted to learn how to do them. Otherwise if I f*ck them up I'll get back to them to do the job...

_________________
"You stay classy OzDat"

No worries mate let me know how you go ive done a few sets before. Take's abit of time and you just need to make sure the double flare's dont leak after you do them

_________________
120Y 4DOOR SEDAN SR20DE WITH ITB'S

http://datsun1200.com/modules/newbb/vie ... post494892

sh*t hope they don't specially onto the new paint!!!!

Yeah I'd say within the next week or so, I'll get in touch with you once I've worked out how I'm going to do them and see what we can come up with. Also would I be able to buy all the material off them including fittings and distribution block???

_________________
"You stay classy OzDat"

Yeah they usually have everything there also modern brake fluid isnt as bad as the old stuff as long as you wash it off straight away the paint will be fine.

_________________
120Y 4DOOR SEDAN SR20DE WITH ITB'S

http://datsun1200.com/modules/newbb/vie ... post494892

Alex the Xmember is drilled & tapped to take a 3 way block.
we can supply the full kit to fit the front brakes.
The 3 way union fits onto the xmember.
the lines run across the rear of the xmember & are scured by "p" clips 7 5mm cap screws.
check this link re the rear lines.
you can do a similar thing.
http://www.datsport.com/Rear_brake_conn ... moval.html

_________________
A little knowledge is a dangerous thing.
www.datsport.com

"R.I.P. Baz. 29 April 2022. Thank you for all your contributions to the Datsun community over the years. You will be missed." - OZDAT

^^^ I see because I basically wanted to do something simillar to Chris (aka Ludachris) bellow is a pic of his setup in his 1600.

_________________
"You stay classy OzDat"

cigarette call me, I got somoene local who he knows your there for me he will look after you.

_________________
]

possibly that was done Before we predrilled the Xmembers.
check yours & you will find the drilled & tapped areas.

_________________
A little knowledge is a dangerous thing.
www.datsport.com

"R.I.P. Baz. 29 April 2022. Thank you for all your contributions to the Datsun community over the years. You will be missed." - OZDAT