Ozdat Home Feature Cars Ozdat Classifieds Event Calander Links Trade Link Tech Resource Merchandise Donate Web Mail
It is currently Fri Mar 29, 2024 9:01 pm

All times are UTC+11:00




Post new topic  Reply to topic  [ 24 posts ]  Go to page « 1 2
Author Message
PostPosted: Mon Feb 25, 2013 1:36 pm 
Offline
User avatar

Joined: Wed Jul 27, 2005 4:45 pm
Posts: 1035
Location: Zombie-free unfluoridated town in QLD
Even bigger bearings on the H20, R16 and U20

Either way the L series is hard to beat :cheers


Top
   
PostPosted: Mon Feb 25, 2013 7:17 pm 
Offline
User avatar

Joined: Sat Dec 15, 2012 4:25 pm
Posts: 74
so I am guessing that 7,000 is a safe rev limit to set on the L18 i have just rebuilt (rotating assembly was ballanced to .4 of a gram) but I am using standard valve springs and a wade 733a cam (i am sure it will taper off power wise after 6,000) but my better half will be driving it in auto cross and she has no mechanical sympathy so I am planning to run an ignition cut at 7,000 unless advised otherwise...


Top
   
PostPosted: Mon Feb 25, 2013 7:41 pm 
Offline
Donating Member
Donating Member
User avatar

Joined: Sun Mar 23, 2003 1:45 pm
Posts: 3200
Location: Newcastle, NSW
Its been a while since my 180B SSS had its tacho (dash is currently wrapped up in a blanket in the shed roof awaiting re-fitting after painting is completed), but I'm reasonably sure that 7000 was the factory redline ????

_________________
1970 ex Group A Rally P510
1971 P510
1972 180B SSS
1965 SP310 Fairlady
1966 SP311 Fairlady


Top
   
PostPosted: Mon Feb 25, 2013 9:24 pm 
Offline
User avatar

Joined: Fri Apr 18, 2008 11:51 pm
Posts: 284
Location: Melbourne Eastern
Sounds right to me. There is a yellow zone on the tacho too, from 6500 I think. I can't check- I put a 240K dash in mine....


Top
   
PostPosted: Tue Feb 26, 2013 9:06 am 
Offline
Guru
User avatar

Joined: Tue Mar 04, 2003 10:09 am
Posts: 2596
Location: Lonsdale, South Australia
datzenmike wrote:
Baz wrote:
L20B bearings a large, due to the fact that the L20B was originally the LD20, a diesel.

Surely the L series came long before the LD20. L16/18s had the same width bearings but smaller diameter. The L20B was a progression of this design introduced in '75 here. I can't find any mention of the LD20 before '78 in the Vanette and '79 in the 910.
We were fitting LD20 cranks to rally engines in 78.
Same spec as L20B , but much better material & for some strange reason, half the price.

What vehicle in North America used the L20B in 75.?

_________________
A little knowledge is a dangerous thing.
www.datsport.com

"R.I.P. Baz. 29 April 2022. Thank you for all your contributions to the Datsun community over the years. You will be missed." - OZDAT


Top
   
PostPosted: Tue Feb 26, 2013 9:41 am 
Offline
User avatar

Joined: Wed Nov 28, 2012 1:59 pm
Posts: 122
Location: Vancouver Island B. C.
August '73 ('74 model; year) in the 610, '75 model year in the 620 truck and 710 (Violet), '77 in the S10, '79 in the A10. Interesting though.


Top
   
PostPosted: Sat Jun 03, 2017 6:10 pm 
Offline
User avatar

Joined: Sat Apr 08, 2017 6:06 pm
Posts: 58
Location: Sydney
so a stock L20B engine can rev to 7000rpm ( red line as said ), is this the same with a series 2 bluebird with all the pollution crap on it as i drive mine and it seem like 3500rpm is to much and a gear change is needed, am i just getting old and forgot how too or are to scared to put the boot in to it :lol:


Top
   
PostPosted: Sat Jun 10, 2017 7:39 pm 
Offline
User avatar

Joined: Tue Dec 30, 2014 7:31 pm
Posts: 47
Location: Banks Pocket, QLD
Prolly already been said but......the shorter the stroke the higher the rev. The old F1 engines may have been v10 or 12 but they probably only had a stroke of 53mm! That's why they could (or had too...!) rev to 18,000RPM +. Add a turbo (or 2) to that and walaha! umungeous unpredictable horsepower.

_________________
Still doing this.....even though the garage is full of Evo 8 MR and X MR Lancers.


Top
   
PostPosted: Sun Jun 18, 2017 7:41 am 
Offline

Joined: Mon May 08, 2017 8:54 am
Posts: 93
I don't know exactly what was done to my Datto nimber3 but it red lined at 8 but I would get 8.5 to 9 out of it.I do know the valves and Pistons were specially machined and fitted to this L 18. the jetting on my webbers were custom too.It was a pig to drive in traffic but once in its rev range it was a rocket.I would not really perform to its optimum with out keeping the revs up to it.I doubled clutched it so as to keep it up near the red line on gear changes and it loved it.You basically had to flog the sh*t out of it all the time.The big thing was it could pull 160 kph For hours on end and not over heat.I routinely would down change from 4 th to 2 nd to clutch break on dirt.Sounds so wrong but it is doable.Awesome way o brake on dirt if you can learn to master it.To be honest on dirt I rarely used breaks.I did however do in lots of clutches.Very few folk drive datto's like that and I don't recommend it.The guy who built my motor is now a highly payed auto engineer.I will be f@&ked if I know how the Brock / Morten BRE race team reliably got 10 k plus and some say even 12.I would personally like to see that.All I know hot 1800.'s + twin webbers are one of the sweetest sounds there is.I am old school so L series motors for me.These days the twin cam transplants are far more practical and better bang for your buck.
DatsEZ


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 24 posts ]  Go to page « 1 2

All times are UTC+11:00


Who is online

Users browsing this forum: Bing [Bot] and 5 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to: 

Powered by phpBB® Forum Software © phpBB Limited