| OZDAT http://www.ozdat.com.au/forum/ |
|
| Toy Tunning Tension Control Rods for Datsun 510 into a 610 http://www.ozdat.com.au/forum/viewtopic.php?t=32851 |
Page 1 of 1 |
| Author: | Super [ Mon Jul 07, 2014 12:58 am ] |
| Post subject: | Toy Tunning Tension Control Rods for Datsun 510 into a 610 |
Hi all, https://technotoytuning.com/nissan/510/ ... datsun-510 Ive emailed Techno Toy Tunning, and they replied that they would not fit into a 610 ???? as they don't have the specs for 610 TC rods I was under the impression the control rods were the same for both 510's and 610's... aren't they? as I would really like to get a set of these but want to be sure they fit first as Toy Tunning weren't any help. lol Mind you I do have a Datsport FJ20 fitting kit installed. FeZ |
|
| Author: | 180BSSSt [ Mon Jul 07, 2014 1:52 am ] |
| Post subject: | Re: Toy Tunning Tension Control Rods for Datsun 510 into a 6 |
Hey Fez, I've owned both a 1600 and 610s and have swapped castor rods between them. You won't have a problem fitting those rods. They look good and aren't dear for the amount of work required to make them. The only thing to check is whether they're legal for street use (if that's a consideration for you). Cheers! |
|
| Author: | Baz [ Tue Jul 08, 2014 11:10 am ] |
| Post subject: | Re: Toy Tunning Tension Control Rods for Datsun 510 into a 6 |
Fez, They are not suitable for a 200B suspension. With out modification. |
|
| Author: | Super [ Tue Jul 08, 2014 3:44 pm ] |
| Post subject: | Re: Toy Tunning Tension Control Rods for Datsun 510 into a 6 |
Hi Baz, I didnt realize that your fitting kits used 200 front end... Good thing I checked. What sort of modification would be needed to fit onto a 200b control arm? FeZ |
|
| Author: | Baz [ Tue Jul 08, 2014 8:26 pm ] |
| Post subject: | Re: Toy Tunning Tension Control Rods for Datsun 510 into a 6 |
Why do you want them? You would be at max caster now. |
|
| Author: | Super [ Wed Jul 09, 2014 11:13 am ] |
| Post subject: | Re: Toy Tunning Tension Control Rods for Datsun 510 into a 6 |
The caster was different for both wheels... I suspect its due to a prior accident the car was involved in on the right hand side of the vehicle. Ive had to add a couple washers to the right side as it sits further forward than the left. My Wheel aligner says its almost perfect now with the washers added, i just thought it be nice to have the adjustment + they look awesome. |
|
| Author: | Baz [ Thu Jul 10, 2014 10:39 am ] | ||
| Post subject: | Re: Toy Tunning Tension Control Rods for Datsun 510 into a 6 | ||
The design of the Techno Toy Tuning adjustable rods places the pivot point in a position that it is too short & alters the caster excessively. This common to this type of design using the rose joints. long radius rods are the cure. Here is a pic of one off proto type adjustables we did on Camos 1600.
|
|||
| Page 1 of 1 | All times are UTC+11:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|