I like it, but paint the the whole grille black leaving just a single stainless line around the outside.
Or get a 73 grille
| OZDAT http://www.ozdat.com.au/forum/ |
|
| Datones 1600 project http://www.ozdat.com.au/forum/viewtopic.php?t=11901 |
Page 14 of 18 |
| Author: | macdatty [ Sun Sep 11, 2011 10:39 pm ] |
| Post subject: | Re: Datones 1600 project |
I like it, but paint the the whole grille black leaving just a single stainless line around the outside. Or get a 73 grille
|
|
| Author: | Anth510 [ Mon Sep 12, 2011 10:25 am ] |
| Post subject: | Re: Datones 1600 project |
Looks terrible, I think you should take it off and give it to me 
|
|
| Author: | SR20Datsun [ Thu Sep 15, 2011 2:07 am ] |
| Post subject: | Re: Datones 1600 project |
Nope. I reckon it looks really really dodgy and has diminished the granny spec look you are going for. Sell it to me... |
|
| Author: | datones [ Sun Sep 18, 2011 9:53 pm ] | ||
| Post subject: | Re: Datones 1600 project | ||
centre mount handbrake now fitted
|
|||
| Author: | SR20Datsun [ Mon Sep 19, 2011 7:30 pm ] |
| Post subject: | Re: Datones 1600 project |
Nice work Tones. 200B centre mount? |
|
| Author: | MYDATO [ Mon Sep 19, 2011 8:07 pm ] |
| Post subject: | Re: Datones 1600 project |
Yep looks like a Poo hundred bee console too me. They fit great in a 1600. |
|
| Author: | datones [ Mon Sep 19, 2011 10:42 pm ] |
| Post subject: | Re: Datones 1600 project |
Yup, 200b centre console with modified datsport handbrake kit. |
|
| Author: | datones [ Mon Sep 26, 2011 9:28 pm ] | ||
| Post subject: | Re: Datones 1600 project | ||
shot from a recent motorkhana....neg camber is a bit much under accel, maybe an adj rear cross member will be next 
|
|||
| Author: | SR20Datsun [ Mon Sep 26, 2011 9:36 pm ] |
| Post subject: | Re: Datones 1600 project |
How'd you go tones? |
|
| Author: | datones [ Mon Sep 26, 2011 10:20 pm ] |
| Post subject: | Re: Datones 1600 project |
Middle of the field Nik, not bad considering it was my first event and i was there really to cut my teeth and gain some experience. A decent handbrake and getting familar with the course would have helped  A vid of one of the runs. Not very exciting, but interesting to see how well the car sat through the corners. http://13thstudio.com.au/exe-deca/b34_orange_datsun.mp4 |
|
| Author: | macdatty [ Mon Sep 26, 2011 11:50 pm ] |
| Post subject: | Re: Datones 1600 project |
Nice work Mate. Car sits well on the road in the vid. And doesn't look to have as much acceleration squat as most SR 1600s. |
|
| Author: | SR20Datsun [ Tue Sep 27, 2011 9:41 am ] |
| Post subject: | Re: Datones 1600 project |
Most of the time acceleration squat also has something to do with traction 
|
|
| Author: | macdatty [ Tue Sep 27, 2011 10:30 am ] |
| Post subject: | Re: Datones 1600 project |
And what happened to the carbon spoiler? |
|
| Author: | datones [ Sun Oct 23, 2011 10:30 pm ] |
| Post subject: | Re: Datones 1600 project |
]Recently decided to upgrade my intercooler which was easy in theory, but that meant i had to totally re-think the way i had my radiator, hoses and support panel. Picked up a 400x 300 cooler (thanks ForumJockey) and pulled apart the old setup. Had to reweld pieces of sheet back into the support panel to repair holes left from the old cooler, then cut out the lower section of the panel to accommodate the new cooler. Folded and touched up the repair (dont look too closely at the panel work ) Attachment: IMG_0683[1].JPG [ 1.64 MiB | Viewed 6247 times ] Attachment: IMG_0686[1].JPG [ 1.84 MiB | Viewed 6247 times ] Attachment: IMG_0693[1].JPG [ 1.67 MiB | Viewed 6247 times ] Attachment: IMG_0687[1].JPG [ 1.74 MiB | Viewed 6247 times ] |
|
| Author: | SR20Datsun [ Mon Oct 24, 2011 10:04 am ] |
| Post subject: | Re: Datones 1600 project |
Nice work Tones. What Rad are you going to run? |
|
| Page 14 of 18 | All times are UTC+11:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|