OZDAT http://www.ozdat.com.au/forum/ |
|
datdrifts 69 510 project http://www.ozdat.com.au/forum/viewtopic.php?t=15073 |
Page 14 of 16 |
Author: | 2DoorTim [ Tue Dec 11, 2012 10:04 am ] |
Post subject: | Re: datdrifts 69 510 project |
Toby, To give you an idea on costs. EFI fuel system. (typically done with a lift pump, surge tank and high pressure pump) Say $200? ECU - Sprint 500 new is $1000. I recently bought a used one for $600. They have an internal map sensor. Injectors $200 Coils $100 Used - $300 new Sensors (Ign Reluctor, Air Temp, Water Temp) $80-$100 Tuning - $300-$500 Moving the ECU from a factory car probably won't work and will probably cost a similar amount to make it work. For example, where would you put the air flow meter? How would you retune those ECU to suit your engine dynamics? Do it properly, save up, and fit something stand alone. Don't be tempted by 'cheap' second hand microtech ecu's off unknown engines either! |
Author: | lampy [ Tue Dec 11, 2012 12:06 pm ] |
Post subject: | Re: datdrifts 69 510 project |
I may be willing to donate a ECU to the cause. Looks like a good project! I have got a Wolf 3d V3, hand controller and basic loom Also have a surge tank You would just need a EFI manifold If your interested all i would want in return is a set of standard late model front lower control arms for a 1600 |
Author: | datdrift [ Tue Dec 11, 2012 2:04 pm ] | ||
Post subject: | Re: datdrifts 69 510 project | ||
Toby,
cheers tim,much appreciated
To give you an idea on costs. EFI fuel system. (typically done with a lift pump, surge tank and high pressure pump) Say $200? ECU - Sprint 500 new is $1000. I recently bought a used one for $600. They have an internal map sensor. Injectors $200 Coils $100 Used - $300 new Sensors (Ign Reluctor, Air Temp, Water Temp) $80-$100 Tuning - $300-$500 Moving the ECU from a factory car probably won't work and will probably cost a similar amount to make it work. For example, where would you put the air flow meter? How would you retune those ECU to suit your engine dynamics? Do it properly, save up, and fit something stand alone. Don't be tempted by 'cheap' second hand microtech ecu's off unknown engines either!
I may be willing to donate a ECU to the cause. Looks like a good project!
That would be awsome and really appreciated lampy. I will grab you some late Lca's .Are you chasing any other bits ?,your offer is too generous,I have a factory 510 tacho ,i will give you some extra bits or throw you some cash with the lca's mate
I have got a Wolf 3d V3, hand controller and basic loom Also have a surge tank You would just need a EFI manifold If your interested all I would want in return is a set of standard late model front lower control arms for a 1600 |
Author: | datdrift [ Fri Dec 21, 2012 3:55 pm ] |
Post subject: | Re: datdrifts 69 510 project |
quik update, I have polished the tapperd cover up,real shinny now.I have used the same datsun 1600 cover for the past 13 years on every donk ive built,its a bit like my lucky charm Spent 3hrs cleaning old paint of my gearbox with the wire wheel.Greased fork pivot and throw out sleeve.Then it took less then 2 minutes to slide box under car and onto motor with the 4 main bolts in,think i broke me record Been tinkering with my 2 different turbo manifold set ups,not liking there placement for a efi set up.So have decided to make another exhaust manifold that sits turbo lower. forgot to bring the camera,pics next time |
Author: | loverdatsun [ Fri Dec 21, 2012 11:20 pm ] | |
Post subject: | Re: datdrifts 69 510 project | |
quik update,
Good work mate.
I have polished the tapperd cover up,real shinny now.I have used the same datsun 1600 cover for the past 13 years on every donk ive built,its a bit like my lucky charm Spent 3hrs cleaning old paint of my gearbox with the wire wheel.Greased fork pivot and throw out sleeve.Then it took less then 2 minutes to slide box under car and onto motor with the 4 main bolts in,think I broke me record Been tinkering with my 2 different turbo manifold set ups,not liking there placement for a efi set up.So have decided to make another exhaust manifold that sits turbo lower. forgot to bring the camera,pics next time |
Author: | datdrift [ Mon Mar 18, 2013 2:01 pm ] |
Post subject: | Re: datdrifts 69 510 project |
Little update, Been busy with alot of things lately,so not much has happened lately on the 69. I have purchased some steam pipe and steam pipe mandrels,t28 flange and cut a flange of some tired extractors,To make the new turbo exhaust manifold. Going to weld some injector bungs into a su manifold,well a good mate of mine is making a custom carbon fibre plenum with vn throttle body to bolt onto the su manifold . I grabbed one of my chopped 1600's to make a dummy engine bay,to build/chop/weld the manifolds in.Dont want to risk scratching up the eng bay in the green car or get weld splatters. Also i have wolf comp to run it now...A HUGE THANKS TO LAMPY FOR HELPING ME THERE Soon as this rain stops,im gonna bolt a dummy l20 into this dummy bay and get this manifold soughted... I have also brought some new sss side vent emblems,mite wait till its closer finnished before fitting.. |
Author: | xfacta [ Tue Jan 21, 2014 8:53 am ] |
Post subject: | Re: datdrifts 69 510 project |
Hi mate, long time no see Any news? Got a datsun on the road? I'll give you a call some time before coming up, not sure when that will be. |
Author: | datdrift [ Tue Aug 19, 2014 1:50 pm ] | |||
Post subject: | Re: datdrifts 69 510 project | |||
Hi mate, long time no see
hey mate,has been a while..not much has changed with the car,rats have got in and chewed on my new door trims.. thats about it..Any news? Got a datsun on the road? I'll give you a call some time before coming up, not sure when that will be. been moving house to much to get back into it.. collected a few more 1600's and tinkinkering with my rs liberty...also been crashed into 3 times over the past year by other drivers on the road..probably a good thing i hadn't got the datsun finnished yet... Also been helping a mate build his stagea up the last couple of years
|
Author: | xfacta [ Wed Aug 20, 2014 9:37 pm ] |
Post subject: | Re: datdrifts 69 510 project |
Hey dude, good to hear an update from you. I hope to come up some time this year with a shopping list of parts. Not a whole lot has changed with our car, just little bits and pieces so it drives a bit better. Let me know if I can ever help you with anything. Wiring and electronics I can do. |
Author: | datdrift [ Sun Aug 31, 2014 3:57 pm ] | |
Post subject: | Re: datdrifts 69 510 project | |
Hey dude, good to hear an update from you. I hope to come up some time this year with a shopping list of parts. Not a whole lot has changed with our car, just little bits and pieces so it drives a bit better.
no worries,cheers bud
Let me know if I can ever help you with anything. Wiring and electronics I can do. |
Author: | green200b [ Mon Oct 13, 2014 9:53 pm ] |
Post subject: | Re: datdrifts 69 510 project |
Any updates Toby? |
Author: | datdrift [ Thu Nov 06, 2014 2:48 pm ] | |
Post subject: | Re: datdrifts 69 510 project | |
Any updates Toby?
nah not really mate... its just sitting under a cover...My mate is starting a shop up soon,so im gonna take it there so i can use his welders and make me manifolds up and get it finished finally
|
Author: | datdrift [ Wed Aug 19, 2015 4:07 pm ] | |||
Post subject: | Re: datdrifts 69 510 project | |||
Been busy on the datsun again, Have had a bit of a break from it and have been setting up our new exhaust and customising shop with a mate in caloundra.. I have the car in at the shop now,so i can get some more done,Went back to the stock 69 dash till i have the car soughted and going then will be going back to the sss fascia.. fitted up the rear sway bar and drilled all the holes back out in the bonnet to reattach the chrome mould...rats had been using it as a home for a while ,so my new door trims had became a bit of a meal for them so I have to remake a couple,also got some new clips to fit them too.. Last few days i have been building the turbo manifold,got it al tacked up last night ready to weld on friday when i get some filler rods for the tig.. Then onto the efi manifold..
|
Author: | datdrift [ Wed Aug 19, 2015 4:12 pm ] | |||||||
Post subject: | Re: datdrifts 69 510 project | |||||||
more pics
|
Page 14 of 16 | All times are UTC+11:00 |
Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |