Chasing a reliable/cheap place to get some strut top plates cut up for my bluey.

Any experiences?

Heres what needs to be done. Thamk you to the orginal creater of this.

Hi waz.

Getting them laser cut would be fairly straight forward. You could also get them water jet cut. Laser cutting should be cheaper though IMHO.

I use and recommend:
Ultimate Laser
www.ultimatelaser.com.au
and speak to either George or Peter.
They are based in Dandenong. Not sure of any other companies more North of Melbourne.

If you only get a couple cut up, they will cost a fair bit. I got my Turbo exhaust flanges cut by these guys and other odds and ends. They turned out sweeet.

_________________
1972 Datsun 1600, S14 SR20DET Engineered (204rwkW @ 17psi.)
viewtopic.php?t=6579
#SR20Datsun @SR20Datsun

'Aztech Cutting Solutions' in Campbellfield are great to deal with.
www.aztechcuttingsolutions.com.au

_________________
Classic Auto Fabrications:
http://www.ozdat.com/forum/viewtopic.php?f=38&t=31659

http://www.lescollinsracing.com/

A mate of mine runs an Engineering shop in Dandenong South - Rob Black Engineering. He could do this - has a laser cutting setup.

He's a fellow car nut with an Elfin clubman that he built himself and races. Ring Ross Black during BH 0402 646 022

_________________
Race car 13B 1600 - since SOLD!
'13 M135i, Quaife LSD, tuned (380 hp)
'15 X5 xDrive 30d tow car
'02 Porsche 996 GT2 (600hp/480rw hp)

I have a feeling I'm the original creator.

Do you have a copy of the .dxf file or have you just got that picture? Your laser cutter friend will most probably want it, or even the solid part. GIve me a yell if you need them.

cheers

Nah only the picture.

A proper file would be tops.

Ill ring arounf tomorrow.

Thx.

If you don't have any luck with the aforementioned parties let me know and I'll see who we use at work. It's the same company every time so they can't be that bad!

_________________
green200b - aka Alistair

The fleet:

Australia:
'80 200B GX - the green200b - hibernating
'81 RX-7 - 12A extend port - daily
'74 RX-2 - 13B bridgeport - cruiser

Europe:
'93 200SX - CA18DET - tourer

So it seems the forum won't let me upload dxf files so send me your email address so I can send you the file.

cheers

I assume you are fitting S13 coilovers?

Yer s13 coilovers, stuffed shocks and cut springs is killing me.

wazz112(at)hotmail.com

Cheers.

We use Laser Plus

_________________
Datsun 1600 13bt

KANARIS ENGINES 03 94623387
http://www.kanarisengines.com/

I'll send through the file tonight when I get home, we also use laser plus as well as a mob called c-tech

Hey peter pantsdown.

Out of interest, you dont work at tyre power essendon do you?
I always spy a similar coloured 1200 sedan parked in a hoist there.

You've got mail.

I work in Port melbourne and the car rarely leaves the garage! It's good to hear someone else has stuck with the datsun mint green though!

And thanks!

Datsun mint green rocks hard.

_________________
1972 Datsun 1600, S14 SR20DET Engineered (204rwkW @ 17psi.)
viewtopic.php?t=6579
#SR20Datsun @SR20Datsun