OZDAT http://www.ozdat.com.au/forum/ |
|
Travis's Datsun 1600....Take 2 http://www.ozdat.com.au/forum/viewtopic.php?t=24896 |
Page 12 of 14 |
Author: | Azzdat16 [ Thu Dec 29, 2016 6:05 pm ] |
Post subject: | Re: Travis's Datsun 1600....Take 2 |
Clean install mate!! Awesome job, she looks amazing. |
Author: | MY110 [ Wed Jan 11, 2017 7:29 pm ] | |||
Post subject: | Re: Travis's Datsun 1600....Take 2 | |||
Next stop after getting it alive is to mod the radiator, start fabbing the exhaust, finish the under dash wiring and get it tuned!
|
Author: | MY110 [ Wed Jan 11, 2017 7:29 pm ] |
Post subject: | Re: Travis's Datsun 1600....Take 2 |
PS cheers for the positive comments guys much appreciated ! |
Author: | MangaNOID [ Fri Jan 13, 2017 11:22 pm ] |
Post subject: | Re: Travis's Datsun 1600....Take 2 |
looking awesome! I can see why you got rid of the red. post a dyno sheet if you can I would love to see how it tunes compared to the stock ecu. what exhaust/muffler are you going with? |
Author: | MY110 [ Wed Jan 25, 2017 8:00 pm ] |
Post subject: | Re: Travis's Datsun 1600....Take 2 |
Thanks MangaNOID, will definately post the results! Planning to go the autech extractors, into 2.5" mandrel stainless system, with decent length mufflers so it's not too loud In other news it runs and now I need to: 1. stop being lazy 2. get exhaust done 3. make intake setup 4. refit modded radiator 5. finish under dash wiring properly 6. refit dash 7. Nistune and dyno |
Author: | SR20Datsun [ Fri Jan 27, 2017 9:10 am ] |
Post subject: | Re: Travis's Datsun 1600....Take 2 |
Some awesome work there with the engine bay. Very envious of the hidden wiring, the cleanliness and the overall 'bling'. Was it easy to re-route the wiring? Any party tricks you can share? |
Author: | MY110 [ Wed Feb 01, 2017 8:07 pm ] |
Post subject: | Re: Travis's Datsun 1600....Take 2 |
Thanks mate! The smoothing of the bay and hiding the loom was done already by Travis, I can't take the credit for that! But I've hidden looms on other Dattos before and it's pretty easy, basically run the loom out the inner guard and around the front of the rad support rather than through the bay. Carefully Mark, cut and extend all necessary wires to be long enough to go the new way around and relocate fuse box etc inside the cab I used a wiring specialties brand loom from the states for the SR motor which went in very nice and neat Now just need to get the finger out and finish this all! Cheers Matt |
Author: | MY110 [ Wed Mar 01, 2017 7:40 pm ] |
Post subject: | Re: Travis's Datsun 1600....Take 2 |
Ok update time ! Radiator back in with new overflow tank all mounted up Under dash wiring done and majority of dash back in ECU Back from Nistune (thanks a million Pete L!) with new R35GTR AFM setup Rocker stoppers installed New VDO SSS dash setup 80 percent done Getting close now! |
Author: | MY110 [ Wed Mar 01, 2017 7:42 pm ] | |||
Post subject: | Re: Travis's Datsun 1600....Take 2 | |||
Dash work
|
Author: | MY110 [ Wed Mar 01, 2017 7:45 pm ] | ||
Post subject: | Re: Travis's Datsun 1600....Take 2 | ||
Starting point
|
Author: | MY110 [ Wed Mar 01, 2017 7:47 pm ] | ||
Post subject: | Re: Travis's Datsun 1600....Take 2 | ||
Getting there
|
Author: | MY110 [ Wed Mar 01, 2017 7:50 pm ] | |||
Post subject: | Re: Travis's Datsun 1600....Take 2 | |||
Radiator in
|
Author: | SR20Datsun [ Thu Mar 02, 2017 9:18 am ] |
Post subject: | Re: Travis's Datsun 1600....Take 2 |
Coming along nicely Matt. It's looking very clean so far and you haven't even finished! |
Author: | MY110 [ Fri Mar 17, 2017 5:42 pm ] | |||
Post subject: | Re: Travis's Datsun 1600....Take 2 | |||
Thanks mate! OK so interior 100% done Rocker cover bolted down for good Just intake, catch can, exhaust and road tune to go!
|
Page 12 of 14 | All times are UTC+11:00 |
Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |