I see my post had been adjusted
| OZDAT http://www.ozdat.com.au/forum/ |
|
| -- Datsun 1600/P510 Project by SR20Datsun -- http://www.ozdat.com.au/forum/viewtopic.php?t=6579 |
Page 72 of 77 |
| Author: | trb012 [ Wed Mar 16, 2016 4:02 pm ] |
| Post subject: | Re: -- Datsun 1600/P510 Project by SR20Datsun -- |
I had my diff done buy XXXXXX in XXXXXX they were really good and Ive never had any drama's with it maybe give them a try? |
|
| Author: | LAG_510 [ Wed Mar 16, 2016 4:27 pm ] |
| Post subject: | Re: -- Datsun 1600/P510 Project by SR20Datsun -- |
Sorry can't help with diff places, did you have all bearings replaced in the diff? Pinion bearings can cause driveline vibes |
|
| Author: | LAG_510 [ Wed Mar 16, 2016 4:30 pm ] |
| Post subject: | Re: -- Datsun 1600/P510 Project by SR20Datsun -- |
Tailshaft? At what speed or rpm? Try taking off the ts and the cvs and turning over the diff to see if there are tight spots? |
|
| Author: | trb012 [ Fri May 06, 2016 3:53 pm ] |
| Post subject: | Re: -- Datsun 1600/P510 Project by SR20Datsun -- |
I see my post had been adjusted
|
|
| Author: | RJB510 [ Thu May 19, 2016 3:26 pm ] |
| Post subject: | Re: -- Datsun 1600/P510 Project by SR20Datsun -- |
What's the latest Nick? |
|
| Author: | SR20Datsun [ Tue May 24, 2016 12:09 pm ] |
| Post subject: | Re: -- Datsun 1600/P510 Project by SR20Datsun -- |
The latest is: I removed the diff from the car early April. The only noticeable issue without taking the back off was a fairly impressive amount of backlash. Dropped it off at the diff shop. They checked the mesh which looked reasonable, but the crownwheel had some abnormal wear and scoring. They pulled it apart in front of me. Nothing seemed to point to an issue until they removed the crown wheel. With the crownwheel out you could feel a graunch on the pinion. It was fairly bad. So out came the pinion bearings for inspection. They looked like they had more than typical wear, but certainly abnormal for only the 110k's that I had done trying to figure out where the noises were coming from. So warranty time. All bearings replaced, no charge including labour to put it all back together. They recommended I get the crownwheel and pinion lapped to ensure no issues when putting back together. I had to pay for this. I could have argued their poor setup caused debris which scored the CW&P, but decided that I would be just happy to get the bloody thing done. So it's back in the car and feels a fair bit better, but still has a period whine (although not as bad) around 75+km/h under partial load which stops after 85km/h. Still enough to really drive you nuts if you are driving in traffic at that speed. Very frustrating. The clunk has disappeared which explained the large amount of backlash. I took it for a drive to ease it back in which included easy drives. I am thinking of changing the oil in it to a 85W-140 with some friction modifier instead of the current 80W-90, hoping the higher viscosity will change the harmonic. I will also be sending out my rear shocks to get them 'short stroked' as the SWR CV joints seem to not like full droop on the passenger side. There's a list of things I need to complete before I will be happy. I ended up fitting a thermax strip to the side of the diff so I can keep track of maximum temperatures. Definitely handy. Attachment: 20160423_123534.jpg [ 92.49 KiB | Viewed 4408 times ] Hoping to be back on the track late this year and have the car drivable for a future wedding... (i've got my priorities right?) |
|
| Author: | Hatchman [ Tue May 24, 2016 1:54 pm ] |
| Post subject: | Re: -- Datsun 1600/P510 Project by SR20Datsun -- |
Congrats on getting engaged mate well done! |
|
| Author: | SR20Datsun [ Tue May 24, 2016 2:30 pm ] |
| Post subject: | Re: -- Datsun 1600/P510 Project by SR20Datsun -- |
|
|
| Author: | trb012 [ Tue May 24, 2016 3:31 pm ] |
| Post subject: | Re: -- Datsun 1600/P510 Project by SR20Datsun -- |
Well done on your engagement mate! |
|
| Author: | SR20Datsun [ Tue May 24, 2016 4:54 pm ] |
| Post subject: | Re: -- Datsun 1600/P510 Project by SR20Datsun -- |
Thanks Stu! |
|
| Author: | LAG_510 [ Thu May 26, 2016 9:07 am ] |
| Post subject: | Re: -- Datsun 1600/P510 Project by SR20Datsun -- |
sh*t, mustn't have pushed submit. Congrats mate! |
|
| Author: | hailest [ Thu May 26, 2016 1:56 pm ] |
| Post subject: | Re: -- Datsun 1600/P510 Project by SR20Datsun -- |
Hey Nik, Congrats to both of you 
|
|
| Author: | SR20Datsun [ Fri May 27, 2016 5:10 pm ] |
| Post subject: | Re: -- Datsun 1600/P510 Project by SR20Datsun -- |
Thanks Trent and Leigh! |
|
| Author: | Anth510 [ Sun Jun 05, 2016 11:36 am ] |
| Post subject: | Re: -- Datsun 1600/P510 Project by SR20Datsun -- |
Congrats mate! |
|
| Author: | hailest [ Sun Jun 05, 2016 2:20 pm ] |
| Post subject: | Re: -- Datsun 1600/P510 Project by SR20Datsun -- |
Whats the latest with the car Nik? |
|
| Page 72 of 77 | All times are UTC+11:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|